Transmission fluid dipstick automatic transmission 11. Calculation 2: Divide total miles traveled by total gallons used. Always disconnect the battery before servicing high current fuses. Steam and scalding liquids released from a hot cooling system can burn you badly. To obtain reimbursement information, U. Remove the jumper cable from the ground metal surface.
Install the new bulb s in reverse order. Allow sufficient time for each gear to engage. Your vehicle comes with two coded keys; additional coded keys may be purchased from your dealer. Install the new bulb in reverse order. Follow the instructions in this chapter. However, if fluid is added at this time, an overfill condition could result when the vehicle reaches normal operating temperature. On vehicles equipped with an automatic transmission, place the transmission in N Neutral ; on vehicles equipped with a manual transmission, depress the clutch.
Pull bulb straight out of socket and press in the new bulb. If this is not possible, wait a short period for the engine to cool. If brake fluid contacts the eyes, flush eyes with running water for 15 minutes. Remove the panel cover to access the fuses. Do not leave the vehicle unattended with the transfer case in the N Neutral position.
Routine maintenance of the air bag is not required. To program additional new unprogrammed key s , repeat this procedure from step 1 for each additional key. For more information on starting the vehicle, refer to Starting the engine in this chapter. Not intended for use on dry pavement. Add 236 ml 8 oz. Make sure the headlamps and electrical accessories are off. Flash to pass Pull toward you slightly to activate and release to deactivate.
With the parking brake engaged and your foot on the brake pedal, start the engine and move the gearshift lever through all of the gear ranges. Department of Transportation-Tire quality grades: The U. Be sure to replace wiper blades when they appear worn or do not function properly. The heater can be plugged in the night before starting the vehicle. Running out of fuel Avoid running out of fuel because this situation may have an adverse affect on powertrain components. These quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle.
Install and tighten the fill plug securely. Use only fluid that meets Ford specifications. Refer to Lubricant Specifications in this chapter. Box 1580, Station B, Mississauga, Ontario L4Y 4G3. Refer to Lubricant Specifications in this chapter.
Service refill capacity is determined by filling the axle to the bottom of the filler hole with the vehicle on a level surface. Allow the vehicle to sit for at least eight hours without starting the engine. Then, start the engine and complete the above driving cycle. The tires may fail and injure a passenger or bystander. Follow one of the simple calculations in order to determine fuel economy: Calculation 1: Multiply liters used by 100, then divide by total kilometers traveled.
If the retractor is not locked, unbuckle the belt and repeat steps two through nine. Be sure to put the cap back on the reservoir. The decisions of the Board are binding on Ford and, in some cases, on the dealer but not on consumers who are free to pursue other remedies available to them under state or federal law. Each seat cushion can be flipped up into the seatback position. Removing the key Turn the ignition off, push the release lever located above the ignition , then turn the key toward you and remove the key. Remove bulb socket from the lamp assembly by turning it counterclockwise. The cover may be removed from the vehicle by sliding it sideways out of the front rail.
Using the armrest if equipped Push the release control to move the armrest up or down. Protect yourself from engine heat. Please take the time to get well acquainted with your vehicle by reading this handbook. Only use the accelerator when you have difficulty starting the engine. Pull headlamp control towards you to turn foglamps on. The belt will still retract to remove any slack in the shoulder belt.
See your dealer or a qualified service technician. Check the coolant level and replenish if low. Position the jack according to the following guides and turn the jack handle clockwise until the wheel is completely off the ground. N Neutral With the gearshift lever in N Neutral , the vehicle can be started and is free to roll. Push the release button at the base of the head restraint post and pull the head restraint up and out. For best results, plug the heater in at least three hours before starting the vehicle. Always set the parking brake fully and turn off the ignition when leaving the vehicle.