AnyConnect Mobile This license provides access to the AnyConnect Client for touch-screen mobile devices running Windows Mobile 5. Step 5 If you have additional Product Authorization Keys, repeat for each Product Authorization Key. AnyConnect Essentials is supposed to be enabled by default. For example, if the main server is down for 20 days, with the backup server active during that time, then the backup server will only have a 10-day limit left over. When you add a new time-based activation key that enables a single feature at the same level as another currently active key, the remaining time from the current key adds to the new key, as shown in Example 3-4.
To avoid unexpected network outages, it is very important to monitor time-based licenses for expiration and replace them in advance; always use permanent licenses for the critical features when possible. Because of this requirement, both units in the failover pair can act as the license server. See the section to determine which licenses you have installed. I was looking for newer versions of anyconnect. As time-based licenses expire, certain features may deactivate completely and some licensed capacities of other features may reduce. It also describes the available licenses for each model.
The shared licensing server responds with information about how often the participant should poll the server. After you upgrade, if you activate additional feature licenses that were introduced before 8. Instructions for installing the license key will be included when you get the license. Example 3-7 illustrates such an attempt. Botnet Traffic Filter License 8. If you install the AnyConnect Essentials license, then it is used by default.
Access in to this host is not permitted. We recommend using this license if you want to support mobile access to AnyConnect 2. Example 3-5 Deactivating a Time-Based Key ciscoasa activation-key d069a6c1 b96ac349 4d53caa7 d9c07b47 063987b5 deactivate Validating activation key. Failover and Temporary Licenses With failover, identical licenses are required. For a license upgrade, you do not need to reload.
Figure 3-2 Failover and Shared License Servers The standby backup server shares the same operating limits as the primary backup server; if the standby unit becomes active, it continues counting down where the primary unit left off. Step 2 reload Example: hostname reload Might be required. See the for more information. Keep in mind that both the current and new time-based keys must enable only one feature with the exact same capacity, if applicable; otherwise, the new key will deactivate and replace the current one. Use the speed command to change the speed on the interface and use the show interface command to see what speed is currently configured for each interface. Time-based features show the remaining number of days before expiration; even if you enable one of these features via the permanent key later on, the countdown will continue until the applicable time-based key expires or becomes deactivated manually.
It is represented by an activation key that is a 160-bit 5 32-bit words or 20 bytes value. If you add another time-based key for 1000 AnyConnect Premium Peers that has a duration of eight weeks, the new key will have the combined duration of 14 weeks. Until you reload, the temporary license continues to count down. The backup server, which has a participant license, can be in a separate failover pair of two backup servers. Regards Vaibhav Hi Marvin, I just bought a any connect plus term license but i am seeing any connect essentials as disabled.
You can also deactivate a previously installed time-based license using the optional deactivate argument at the end of the activation-key key command, as shown in Example 3-5; this keyword is not available for the permanent activation key. Instead, you can have a second pair of units acting as the backup server, if desired. This process is required to meet Federal regulations surrounding the use of strong encryption. This license is applied by simply using the activation-key command. The mobile license is on or off and not tied to a number of users.
The last license you activate is the one in use. When the load is reduced on a participant, it sends a message to the server to release the shared sessions. Viewing Your Current License This section describes how to view your current license, and for temporary activation keys, how much time the license has left. Detailed Steps Command Purpose On the active unit: Step 1 no failover Example: active config no failover Disables failover on the active unit. Can any one confirm that my understanding is correct, or would i need to buy a seperate Premium license a long with the mobile client license to enable this functionality? Is there a way to find whatever Activation License is tied to my device from Cisco without a service contract? Example 3-2 Successfully Activated Permanent Key ciscoasa activation-key 813cd670 704cde05 810195c8 e7f0d8d0 4e23f1af Validating activation key. Once you've installed the key and rebooted, running the 'show version' command should indicate that the license is enabled.