Start at the bottom and insert the anchors into the slots and turn them through 90 degrees - a pair of long nose pliers might help. It's hard to tell from your pictures, but I can see a few holes where 10mm bolts could go. I have a fear of snapping anything plastic, especially in cool to cold weather. With the barrel pointed at my face. I've always hated the A-pillars in my truck.
Using a screwdriver, remove the front pillar garnish cover. Refer to Headliner Removal and Installation for proper procedures. Employ the same manner described above to the other side. I'm confident in the fact that as long as power is not applied to the squib, nothing is going to happen. Bill Hi Bill this really helped me I had a 13 and I just got a new 15 and it's different it looks like it's made to be popped out to have access to that panel.
Aug 07, 2014 Google year make model sunroof leak and there will be a video. If this hangs up,it will cause poor flow the right way fuel goes in the tank. Did you read post No6? Using a screwdriver, remove the lens. In at the bottom first then push those clips through and turn through 90. Been out of t'internet range so catching up.
There are multiple routes that I can take the wire. Anyway, the trim does not want to go back on. Extreme care must be taken when removing the motor, timing may be thrown off causing possible damage to the sunroof system. Using a screwdriver, remove the lap belt outer anchor cover. Maybe I could do this. Correct me if I'm wrong, but your airbag needs an electric signal from the sensors on the car to be sent to the pyrotechnic charge. Break the clips and say f It? Install room partition board lh separated type rear seat 38.
It looks amazingly clean and is going to be perfect for either a cell phone or Ham radio controller. All you do is, starting at the top either with your fingers or long nose pliers, just turn the clips through 90 deg and they will then detach. Pull gently from the top, detaching the clip above the bolt, then the claw below the bolt. Is the thing going to pop open and smash me in the face as soon as I remove the screws from the grab handle and remove the trim? Make sure both parts are unbroken. I brought the cable along the headliner, down the channel, along the bottom of the pillar, then behind the front door weatherstrip down to the side kick panel. Unbolt it, and pull up slightly towards the headliner to clear the dash, then it pops right off. I'm looking to remove the trim piece that the oh-shit handle is attached to.
Posted on Aug 16, 2009 If your motor is audible and your fuses and connectors are okay, you may have to take a close look at the plastic gear parts up in the roof. I couldn't fit the drill+bit into the head of the screw because the steering wheel was in the way. I'm not sure that poking around a pillar is going to really have an effect on the airbag system. Obviously I will be very careful when doing anything in there. It is not tethered and comes completely out. Hint : tape the screwdriver tip before use. Actually, it's the trim I hate.
If not, you have to pull out the rear seat, back and bottom. Remove lh visor assy 29. Hint : tape the screwdriver tip before use. Remove cowl side trim board lh 7. I opted for the fog lamp to 1 save wiring and hassle; and 2 as the camera is a 'nightvision' one and the glare of the licence plate lights would have troubled it: Back in the car, working: If you imagine the book you can see just at the bottom left of the screen were a wall or post, then the spare wheel cover would be just about to touch it. .
Next Remove Black Piece By The Window By Pulling It Strait Outward. Otherwise it is supposed to hold the trim partly away from the A post if the airbag deploys, so it is fairly strong. Employ the same manner described above to the other side. Remove front door opening trim rh 8. Body panel replacement in this manual 2. Illustration of weld point symbols. If there really are some pins, same thing works, or a thin flexible spatula and go slooooooooooow yep.