Overall I really like the way that this hitch is hidden, up behind the fascia here, other than what you're able to see that comes out right underneath there. Needed die grinder with cut-off wheel to complete install, a tool not always available to average consumer. Overall well built and well designed. Also, you can see how tightly this receiver tube is up towards the fascia here, so that's going to help maintain that clean look, but that's also going to help give plenty of ground clearance. Took much longer than it would have had we had power tools, instead of hand wrenches. My issue occurred after the install.
So now we can go back and make sure everything is torqued to the specification in the instructions. Listed below are the Trailer Hitches that are designed to work with the 2012 Toyota Yaris. Great customer service and fast shipping. Manufacturer: Curt Manufacturing Part Number: 11050 Rating: Class I Receiver Size: 1. Now, let's show you how to install it. So now we can take a half inch wrench or socket and begin to tighten them up.
So once we put our hitch up into place, we'll be replacing the bolts that we took out with our new ten millimeter bolts with conical tooth washer. Then we can go back and get the rest of our hardware started. We can go back and reinstall the little plastic popper to this. I think it's going to do a really good job of carrying any hitch mounted accessories, like bike racks or cargo carriers that you may want to use with this. So now what we'll need to do is we'll need to take these two bolts out from these weld nuts. Various towing accessories like electrical wiring and hitch steps allow you to take with more confidence.
It's a good idea to grab a second set of hands just so you can pull these tabs down and feed it up over the exhaust on the passenger side, then you can work it across so you can get it up into position. I tried to use a chisle to get it out but that only rounded the piece over. Need assistance selecting the right Draw-Tite product? This configuration is ideal if you already have a ball mount, or if you intent to use the hitch for aftermarket accessories like bike racks or cargo carriers instead of for towing. Toyota trailer hitch product reviews are done by Toyota Yaris drivers just like you. We had to purchase a tap and die set to recut the threads in the frame of the vehicle. The vehicle information you have entered has triggered this alert.
Would definitely buy from them again. Entering your vehicle information in our Year Make Model selector up top, helps ensure you get an auto part that fits your car, truck or other type of vehicle. You will want to be sure to refer to the vehicle's owner's manual to see what type of weight the vehicle's rated for. The mounting holes on the frame of the 2002 Honda Odyssey were a mess, due to rust in the threads. We've got the teeth on this side here, so they'll go down away from the head of the bolt and in towards the hitch when we put them into place.
All you can really see is the end of the receiver tube opening here which is inch and a quarter by inch and a quarter, and then the rolled steel safety chain loops right here. Full transcript: Today on our 2011 Toyota Yaris we're going to be taking a look at and installing the Draw Tite Sportframe Class 1 Trailer Hitch Receiver, part number 24819. In the end , I had to grind a groove in order to slide past the excess steel. Now, I'll give you some measurements to help assist you with your selection of hitch mounted accessories. The best part is, Yaris towing products always are shipped to you completely free. I went to install my bike rack and found a chunk of weld inside.
We have worked hard to design a site that caters to everyones Toyota Yaris Hitch needs. Please consider the condition of your Tow Vehicle. Please review the vehicle options and installation notes, to ensure you select the correct product for your Toyota Yaris. Towing a trailer can be demanding on some older vehicles, depending upon their condition. The distance from the center of the hitch pin hole to the outermost part of the rear bumper is three and three quarter inches and the distance from the top inside edge of the receiver tube opening to the ground is twelve and three-quarter inches. In order to do so you can take a flat head screwdriver, pop the center of them out and the body of them should come right out, so I'll do that same thing on that other one.
If it's not rated for that weight, you'll want to be sure to go by the guideline in the manual. Then you can get one of your bolts started with conical tooth washer on either side. We're here to help you find that perfect Hitch for your Toyota Yaris. Draw-Tite, a leading aftermarket manufacturer of top-notch towing systems, is unsurpassed in price and quality. When you pick up your order instead of shipping it to your home, you may see additional savings as some products will be priced lower for in-store pickup.
. Virtually every Toyota Yaris can modify into a mighty camper hauling machine with trailer hitches from Auto Accessories Garage. That is why when searching for Yaris towing products Auto Accessories Garage does it best. Then we'll remove these two bolts the same way. It took longer than the time stat. If you are planning to tow a trailer, for use over any distance, you should consider the condition of your tow vehicle. Every Toyota hitch is specifically designed to your Toyota Yaris to fit perfectly.
This hitch features a 200 pound max ton weight rating and a 2000 pound gross trailer weight rating. This hitch is sold without a ball mount, pin, or clip. We love when auto parts experts come to our site and we love when car parts newbies come to our site. We're here to help - please call us at 1-800-358-4751. Better than ebay and amazon and I'm a prime member.