Beetle Sport Hatchback 2001 License Plate Base Front Part : 1C0-807-287-L-B41 -M58 Beetle 2009-10 Beetle 2. This photo shows the connection at the base of the intercooler. You'll have to take the arm rest off so unscrew that and take off. Sounds hard but it come right out. It wasn't as easy as it sounds, though.
There are instructions printed on the black plastic above it. The last thing is to remove the stick. I also recommend removing the plastic duct that leads to the side-mounted intercooler. The lamp itself is held on with another ring that's attached to the car with three screws. In front of the battery, if you look with a flashlight, you will see the primary locking mechanism. It's true that turbocharged cars often have some oil in the intercooler piping, as crankcase ventilation lines lead into this piping in order to send oil vapors into the intake stream, where they can be burned by the engine. You can also use this article to remove the front grille.
Undo the 3 bolts on the bell-housing that holds unto the sump, you will need a 5mm ball-end allen socket. After pushing the lever completely toward the headlight, the headlight will pop out the front of the car. It's held on with one screw at the bottom. In order to improve access to the front of the engine, Audi created an ingenious solution. In other words, it is a procedure that must be done before performing many other projects on the A4--so many that it deserves its own write-up.
Beetle Sport 2002 Without Headlamps washers. All pictures and references to the Porsche name, and the car names and shapes are for restoration reference only, and do not imply any association with Porsche. When you change the foglight on your Beetle, be careful not touch the glass part of the bulb with your fingers which causes the bulb to burn out earlier. Are you asking how to tell if you are 180°out? We can make all your dreams come true with improved Beetle Front Bumper. Aerosol Can Part : 120077 -M1256 Loosen, lubricate and protect home and commercial locks. A secondary locking mechanism still holds it in place. To find your paint code: You may want to look in the following places: -Inside the trunk Not sure if the part fits your vehicle? Unscrew nut size 32 from the shaft.
Figure 28 I loosened the hose clamp, removed the hose, and was surprised to find a few ounces of oil on the floor of my garage. Remove the 8x T25 torx screws along the bottom lip of the bumper. We will provide instructions on the necessary steps to exchange the item or receive merchandise credit. Give our parts specialists a call at 1-888-280-7799. Just open the back of the housing and replace the bulb that is out. An important detail is that it is locked in place by a small sheetmetal latch near it's base. Tighten and replace rock shield.
It has 3 or 4 screws on top and then is detached from the bumper by pulling at the bottom of the grille. It's possible that a smaller rod might not hold the weight of the radiator support panel as well, but you could supplement the rods by placing something on the floor under the panel. As it comes forward, wiggle the side marker lights out. At this stage I'm unsure if this is a bad sign or not. The only other possibility is if you have headlight washers but this should be obvious.
. It hangs over a little lip against the window. Excellent pictures and explained very well. The 2 fenders and the hood come off together as 1 piece. This is what will come off. You need to protect it from scrapes and manipulate it a bit to disconnect some wiring and plumbing.
This photo shows the passenger-side grille. This is necessary to service the headlight washers and to reach the radiator drain petcock in the case of the 1. This grille feeds air to the duct that supplies the side-mounted intercooler. Easily reach into narrow lock mechanism with the attachable straw or use the wider spray pattern to refurbish and protect the entire lock. It is practically invisible even with a flash light.
If we get a chance to perform the procedure, we will be sure to document it. It may also be covered with dirt making it dificult to see as well. July 29, 2015 Followup from the Pelican Staff: The bumper support? Wedge your fingers under the black plastic edge of the bumper to pry the fasteners loose. Figure 8 Next you can start separating the bumper from the car. January 16, 2016 Followup from the Pelican Staff: Thanks for the feedback. I had to cut the zip tie in order to move things along.