Please let us know what happens. The following day, I took the car to a different dealer, where they tested the car but made no repairs. It's so much that I can pick away at it with a flat head. The currently selected is for the Hyundai makes. The Crankshaft sensor will be in the engine block, down lower. You can tell where the line is, it's where your head gasket goes. Beck Arnley's years of experience and proficiency in global sourcing provides vehicle owners the precise part for the right and most up-to-date vehicle applications.
The changing gap causes the magnetic field near the sensor to change. I did do a simple tho as well. No matter the situation, Advance Auto Parts has the Crankshaft Position Sensor product you desperately need. I changed it myself, seemed pretty easy. So I took out my computer check tool and it said the crankshaft sensor was bad. They could find no problems.
When the engine is running, the high and low parts of the teeth cause the gap with the sensor to change. Ok, I'm pretty sure I replaced the correct sensor. The sensor I replaced was located near the valve cover passenger side on the back of the cover. This information is used by the Engine Control Module to control ignition and fuel injection. My mechanic noted that the cam shaft sensor may have been knocked a few times by the belt? The change in the magnetic field cause the voltage from the sensor to change. . A regional representative contacted me and asked that Hyundai have an attempt to fully investigate.
Important: Twist sensor from side to side before removing Disclaimer: This video is not meant to be a definitive how to. Maybe you can find a short somewhere. Hyundai deemed the car okay because the technician went for a 15 mile test drive; the car has had three potentially fatal incidents in 22,491 miles. Could someone help me locating a cam shaft position sensor on my engine? Your mechanic could be one tooth off-but Hyundai does not say if that will kick a code-unlikely the chain jumped, but who knows? I went to the Hyundai dealership and asked a mechanic. Also a crankshaft position sensor looks exactly the same as a cam shaft sensor.
Code is still on This is the one I replaced. The symptoms were very similar to the March 4 incident, without the stalling out on the highway to preface it. The change in the magnetic field cause the voltage from the sensor to change. A dealer replaced the crankshaft position sensor. Install camshaft position sensor in rear of cylinder head. We have worked hard to design a site that caters to everyones Hyundai Tucson Crankshaft Position Sensor needs.
Called my mechanic, said it is most likely the camshaft sensor. I had an appointment at the dealer I purchased the car from, and the regional representative contacted them to coordinate examination of the car. It had a code about too much fuel in the system honestly forget what the code was. A dealer examined it and consulted with Hyundai tech line but did nothing. By buying a new replacement part, you can save hundreds, even thousands of dollars in costly auto repairs later down the road.
This information is used by the Electronic Control Module to control ignition and fuel injection. The camshaft position sensor senses the piston position. Disconnect wire connector from sensor. A representative at the regional office said the they replaced the power control module based on incidents in other cars, where the error code for the crankshaft position sensor has come up. Have parts delivered straight to your home, or find the nearest Advance Auto Parts store to check out our Crankshaft Position Sensor stock in-person! I had a similar problem years back with a Mitsubishi Eclipse. A bad or malfunctioning crankshaft sensor will often cause a service engine light error code, and or cause a no start condition, or rough running due to inaccurate ignition and fuel timing. For more information: We know car parts and we know auto parts.
You know the code, but there are a lot of variables in the timing belt. The crankshaft sensor is above the starter on the side of the block. Since 1919, Standard Motor Products has engineered a full line of engine management products, including ignition parts, sensors and on-board computers. I also found another sensor had same 3 pin connector near the transmission? Enter the 5 character trouble codes in the search box and submit the search. Our electrical and electronic parts are subject to strict quality testing. Always consult a professional repair manual before starting your repair. Select Year for Hyundai Tucson Crankshaft Position Sensor.
Year Make Model Description 2001-2006 Hyundai Santa Fe Hyundai Santa Fe Crankshaft Position Sensor V6 2. Any ways the original timing belt was so stretched it was bringing up a emissions problem. As of right now my car starts every time but i'm thinking that will change soon if I don't do something about this engine code. We have 8 reviews on our Crankshaft Position Sensor products for the 2004 Hyundai Santa Fe from previous customers. P0335 Hyundai Description The Crankshaft Position Sensor also known as the crank position sensor is an electronic device used in an engine to record the rate at which the crankshaft is spinning. The camshaft position sensor senses the retraction of camshaft intake to identify a particular cylinder. They asked to be able to send a regional technician to look at it.
If you have any doubt as to repairs on your vehicle, please contact your technician. You should make out the plug with the wire and see that the sensor is being mounted with 1 10mm bolt. That it may need to be replaced. So you have dual overhead camshafts, but the timing belt only drives one of them. Cheers I looked for about an hour last night in this area and could not find it. I have no idea what the problem could be. That is the correct sensor.