Take off the tank skid plate thingy. Allow 8-10 weeks for delivery after rebate end date of each claim. Your Jeep Wrangler fuel pump uses pressure to send the right amount of gas from the fuel tank to the engine. Shipping to Alaska and Hawaii will require an additional charge. Tires and Wheel and Tire Kits do not qualify for free shipping. The following steps are based on the 2003 to 2006 Jeep Wrangler models.
The Vintage Mechanical Fuel Pump comes with all mounting hardware, gaskets and instructions needed to install it. The unit is capable of reliably supplying fuel via diaphragm pressurization even under severe engine load, so you know you can count on it when the going gets tough. That took care of thestalling when engine came off fast idle. I'm considering by-passing the line from the power dist center Fuse block back to the fuel pump itself. Place a floor jack underneath the fuel tank for support, then remove the 3 tank mounting nuts located at the front of the tank and the 4 mounting nuts at the rear using a wrench or ratchet and socket; then lower the tank and the protective plate underneath the tank as a single unit. Once it comes off fast idle it stalls and will not restart until things have cooled and choke is engaged again.
Mounted in the fuel tank on top. A small hole in the fuel lines, for instance, will adversely affect driving performance, while a bad fuel pump will leave you stranded every time. Before starting work, always ensure your vehicle is on level ground with the tires chocked and the battery disconnected. Relieve the fuel system pressure by depressing the small stem inside the Schrader valve located on the fuel supply line just before the first fuel injector. You might have to lower the tank a bit before you can get the lines and connectors disconnected.
A new fuel filter is recommended when replacing. Ther is lots of spark coming from the plugs and it sounds like she wants to start. They either work or they don't. When replacing the fuel pump, make sure your Jeep is not around any open flames or cigarettes. Unplug the electrical connector located on the left and front of the fuel tank and the two vapor lines next to the electrical connector by pressing the lock tabs.
Before starting work, always ensure your vehicle is on level ground with the tires chocked and the battery disconnected. This part generally fits Jeep vehicles and includes models such as Cherokee, Wrangler with the trims of Base Sport Utility 2-Door, Base Sport Utility 4-Door, Chief Sport Utility 2-Door, Chief Sport Utility 4-Door, Islander Sport Utility 2-Door, Laredo Sport Utility 2-Door, Laredo Sport Utility 4-Door, Pioneer Sport Utility 2-Door, Pioneer Sport Utility 4-Door, S Sport Utility 2-Door, Sahara Sport Utility 2-Door, Sport Sport Utility 2-Door. Removing and installing the fuel pump on your Jeep Wrangler requires careful work to avoid damage to the fuel and vapor lines. Spark plugs are shooty, rich mixture???? The pump has a steel braided line and a nylon plastic line attached to it. Put a jack under the tank and undo the straps.
Oversize fees also waived on this item. Tools Used: Tools, Wrench set, Shop towels Replace a Fuel Pump Lift the hood and prop it open. The Vintage Mechanical Fuel Pump fits all 1987-1990 4. Precision castings and hardened rockers help ensure a long life. Continue to lower tank and remove.
You'll see it on the item page as a Vendor Handling fee, and it will show up in the cart below the item s you're ordering. Install the pump assembly in the tank with a new O-ring seal gasket. Free Shipping Offers are for Standard Ground Delivery Service and are only valid for shipping addresses within the 48 contiguous United States. Disconnect the black, negative battery cable and loosen the filler cap. Fitment: 1987 1988 1989 1990 Word On The Trail This company has always been the go-to site for good deals, good products, and service. Tools Used: Tools, Wrench set, Shop towels Replace a Fuel Pump Lift the hood and prop it open.
My Jeep was my first vehicle, and first and only Jeep so far but I know there will be others. The jeep won't start but if i pour fuel into the carb it does for a few seconds. Use this info at your own risk! Follow the fuel lines if you cannot find it still. It looks like the tank is attached by only straps and once the tank is dropped, the process should be much clearer. There s not much guessing with a fuel pump. I never have had problem with the products sold, even after several years of use.
A broken fuel pump, though, can turn your Wrangler into a frustrating and pricey ride by causing the engine to jerk upon acceleration and consume too much gas. Hi, I'm not getting any fuel to the carb. So if you do this, the 15 gallon sending unit will not accurately read the fuel level of the now 20 gallon tank. Remove the locking from the assembly using tool 9340. Unplug the electrical connector located on the left and front of the fuel tank and the two vapor lines next to the electrical connector by pressing the lock tabs.
I am assuming that if it will run with the choke on when it is cold that gas is flowing. Install the locking on the module and rotate the ring by hand until the embossed arrow points to the center aligning mark on top of the assembly--the same position as before disassembly. Connect the filler hose to the tank; then lift the fuel tank into its mounting position and tighten the tank mounting nuts. This means that the fuel pump attaches to the engine block and is not located inside the gas tank, as it is on most vehicles. Changes in pressure lead to inconsistent streams of fuel. The Vintage Mechanical Fuel Pump comes with all mounting hardware, gaskets and instructions needed to install it. Remove the pump module locknut using tool number 6856, if you have a 2003-2004 model.